EQ-004 — Ocean Signal ATB1 AIS transponder
← Equipment Register · Browse equipment
Survey status: Owner-confirmed installed and located; wiring not verified. The owner identifies this equipment on the COM frame (
SL-COM) in the starboard-forward saloon beside the DC panel. Installation specifics (wiring, protection, interconnections) are not independently surveyed; manufacturer figures below are reference data, not measurements.
Identity and location
| Field | Value |
|---|---|
| Permanent equipment ID | EQ-004 |
| Equipment | Ocean Signal ATB1 AIS transponder |
| Register category | Communications |
| Equipment class | EQ |
| Reported location | SL-COM — COM frame, saloon, starboard-forward side adjacent to the DC panel (owner-confirmed) |
| Inventory state | Owner-confirmed installed; location known; electrical configuration unverified |
| Manufacturer / model | Ocean Signal ATB1 Class B SOTDMA AIS transponder |
| Serial / part number | Not recorded |
| Last onboard verification | Owner-reported location, 31 October 2026; physical electrical survey outstanding |
Original reference and notes: Source inventory says AIS; owner confirms the Ocean Signal ATB1 at the COM frame.
Electrical installation — as fitted
| Field | Surveyed value |
|---|---|
| Supply voltage / input | Not measured or recorded |
| Source / distribution busbar | EQ-001 main DC panel → EQ-057 four-way fuse board (owner-confirmed functional path; upstream CB-003 10 A owner-confirmed) |
| Supply branch circuit | DC-COM-04 — feeds this equipment, distinct from equipment ID |
| Primary branch protective device | FU-003 3 A, EQ-057 way 3, protecting DC-COM-04 — owner-confirmed rating/position; fuse format and conductor size unverified |
| Upstream protective device | 10 A CB-003 via DC-COM-01 to EQ-057, owner-confirmed; separate branch fuse unrecorded |
| Cable / terminal references | See source notes and connections below; unverified until traced |
| Cable size, fuse/breaker rating and measured load | Not recorded |
Important: a device’s manufacturer-rated input, current or recommended fuse is not proof of the actual cable, protection or wiring aboard Ragtime.
NMEA 2000 connection
Owner-confirmed, 6 November 2026: Connected to segment A for data only. The equipment’s operating power remains on its separate COM-frame DC circuit. See the segment A connection and power table. Network interface/adapter hardware, drop route and pin-level connections remain to be documented; no direct connector or interface model is inferred.
Known or reported relationships
EQ-057— owner-confirmed ATB1 output way 3, 3 A FU-003, circuit DC-COM-04.EQ-005— owner-confirmed Digital Yacht SPL2000 RF connection to AIS port.EQ-058— common masthead antenna connected through the splitter.EQ-003— VHF radio shares the masthead antenna through SPL2000; both devices have owner-confirmed data-only connections to NMEA 2000 segment A, with interface wiring untraced.
See the COM-frame functional supply and RF paths.
The NMEA 2000 network record records the current owner-confirmed segment A allocation separately from the historical configuration notes.
Manufacturer reference
Identification confidence: ATB1 identity and COM-frame installation confirmed by owner; serial number and wiring pending.
- Manufacturer: Ocean Signal; Class B SOTDMA AIS transponder, with built-in GNSS.
- Vendor manual describes a 12/24 V DC installation with NMEA 2000, NMEA 0183, USB and Wi-Fi connectivity.
- The manufacturer’s installation illustration calls for a 3 A fast-acting fuse. This is manufacturer guidance, not an assertion about the fuse installed on Ragtime.
- An appropriate active AIS/VHF splitter is required for shared-antenna operation; owner confirms the fitted Digital Yacht SPL2000.
Documentation
Information requested from the owner
- ATB1 supply is confirmed as way 3 (FU-003, 3 A), upstream CB-003 10 A. Check the fuse format and branch conductor size.
- Can you provide an ATB1 nameplate photograph and confirm its power cable size?
- Segment A data-only connection is owner-confirmed. Record its drop route, network interface and connector details when available.
Record maintenance
- Evidence basis: existing website inventory and owner confirmation of COM-frame location on 31 October 2026; manufacturer documentation where model identifiable.
- Verification: owner-confirmed fused-board supply and shared RF path; installed fuse values, wiring, serial and network connections await survey.
- Avoid publishing passwords, SIM identifiers, access tokens or other confidential credentials on this public site.