EQ-005 — Digital Yacht SPL2000 AIS/VHF splitter
← Equipment Register · Browse equipment
Survey status: Owner-confirmed installed and located; wiring not verified. The owner identifies this equipment on the COM frame (
SL-COM) in the starboard-forward saloon beside the DC panel. Installation specifics (wiring, protection, interconnections) are not independently surveyed; manufacturer figures below are reference data, not measurements.
Identity and location
| Field | Value |
|---|---|
| Permanent equipment ID | EQ-005 |
| Equipment | Digital Yacht SPL2000 AIS/VHF antenna splitter |
| Register category | Communications |
| Equipment class | EQ |
| Reported location | SL-COM — COM frame, saloon, starboard-forward side adjacent to the DC panel (owner-confirmed) |
| Inventory state | Owner-confirmed installed; location known; electrical configuration unverified |
| Manufacturer / model | Digital Yacht SPL2000 — confirmed by owner (31 October 2026; no serial/nameplate photo yet) |
| Manufacturer part number (reference only) | ZDIGSPL2000 — verify against fitted unit |
| Serial number | Not recorded |
| Last onboard verification | Owner-reported location, 31 October 2026; physical electrical survey outstanding |
Original reference and notes: Source inventory lists a communications splitter; owner confirmed COM-frame location and subsequently explicitly confirmed Digital Yacht SPL2000 identity on 31 October 2026. Serial number and installed fuse values remain unrecorded.
Electrical installation — as fitted
| Field | Surveyed value |
|---|---|
| Supply voltage / input | Not measured or recorded |
| Source / distribution busbar | EQ-001 main DC panel → EQ-057 four-way fuse board (owner-confirmed functional path; main-panel upstream breaker unrecorded) |
| Supply branch circuit | DC-COM-03 — feeds this equipment, distinct from equipment ID |
| Primary branch protective device | FU-002 3 A, EQ-057 way 2, protecting DC-COM-03 — owner-confirmed rating/position; fuse format and conductor size unverified |
| Upstream protective device | 10 A CB-003 via DC-COM-01 to EQ-057, owner-confirmed; separate branch fuse unrecorded |
| Cable / terminal references | See source notes and connections below; unverified until traced |
| Cable size, fuse/breaker rating and measured load | Not recorded |
Important: a device’s manufacturer-rated input, current or recommended fuse is not proof of the actual cable, protection or wiring aboard Ragtime.
Known or reported relationships
EQ-057— owner-confirmed SPL2000 output way 2, 3 A FU-002, circuit DC-COM-03.EQ-003— owner-confirmed RF coax connection to Icom M510 at the SPL2000 VHF port.EQ-004— owner-confirmed RF coax connection to Ocean Signal ATB1 at the SPL2000 AIS port.EQ-058— Vesper VA159 via a single continuous, unjointed length of Ancor white RG213 coax, internally down the mast, through the swan-neck deckhead entry to the splitter antenna input; no intermediate RF connectors (owner-confirmed).
See the COM-frame DC and RF path overview. VA159, RG213 type and route, and the absence of intermediate coax joints are owner-confirmed. The cable length is owner-estimated at mast height + 3 m (not measured); no SWR readings exist. Both end terminations use soldered PL-259 connectors (owner-confirmed). Connector condition, weatherproofing and the optional AM/FM output remain to be surveyed.
Manufacturer reference
Identification confidence: owner-confirmed Digital Yacht SPL2000. The exact manufacturer model is now confirmed by the owner; installed supply voltage, individual protection ratings, serial number, cable and coax particulars are not physically surveyed. Manufacturer specifications below are reference values, not measured onboard results.
Manufacturer’s published specifications (SPL2000)
| Property | SPL2000 manufacturer reference |
|---|---|
| Function | Active Class B AIS/VHF antenna splitter, sharing one VHF antenna with AIS transponder and VHF radio; optional AM/FM radio feed |
| Nominal DC supply | 12 V or 24 V DC |
| Published input-voltage range | 9.6–31.2 V DC |
| Current consumption | Less than 150 mA at 12 V DC |
| Recommended branch protection | 1 A positive-feed fuse or suitable circuit breaker (per installation manual; installed rating not yet known) |
| Power-lead colour convention | Red = DC positive; black = DC negative (manual, not verified on boat) |
| RF connectors | VHF antenna and VHF radio via PL259/SO239 coax connectors; AIS transponder via BNC coax connection (manual) |
| RF port impedances | 50 Ω for AIS, VHF and antenna; 75 Ω for optional FM port |
| VHF input power limit | 25 W maximum |
| AIS input power limit | 12.5 W maximum |
| Enclosure | Water resistant; install below deck in a dry location |
| Compass clearance | 0.5 m minimum (per manual) |
| Loss-of-power behaviour | Manufacturer states VHF-to-antenna path remains available on splitter failure or loss of supply |
The owner confirms the splitter connects to the Icom M510 VHF, the Ocean Signal ATB1 AIS and a shared masthead VHF/AIS antenna. These are documented functional RF relationships; connector type, routing, condition and AM/FM output are not physically surveyed.
Manufacturer sources and manual
Important: The manual’s 1 A figure is a manufacturer recommendation, not an entry in Ragtime’s Circuit Register. Allocate a protective-device ID and validate its conductor/protection arrangement only after an onboard trace.
Information requested from the owner
- SPL2000 supply is confirmed as way 2 (FU-002, 3 A), upstream CB-003 10 A. Check fuse format and branch conductor size.
- Can you provide a nameplate/rear photo for serial number, coax connector types, and cable routing?
- Is the optional AM/FM radio output used? The continuous RG213 feeder ends in a soldered PL-259 at the SPL2000 antenna input (and another soldered PL-259 at the VA159). Connector condition and weatherproofing can be checked when convenient; no SWR readings are available.
Record maintenance
- Evidence basis: owner-confirmed COM-frame location, confirmed SPL2000 identity, owner-reported fused DC feed and shared antenna RF relationships (31 October 2026); manufacturer manual for rated specifications.
- Verification: identity, location and functional paths owner-confirmed; physical connector inspection, nameplate/serial, fuse protection and cable sizes remain open.
- Avoid publishing passwords, SIM identifiers, access tokens or other confidential credentials on this public site.