EQ-021 — NASA Marine Combi tricolour/anchor masthead LED

← Equipment Register · Browse equipment

Owner-confirmed fitted equipment and circuit role, not independently tested. NASA Marine Combi masthead tricolour/anchor LED, fed through the original Moody NAV LTS panel. Exact installed model suffix, conductor sizes and electrical measurements are not available. Navigation-light system.

Identity and location

FieldValue
Permanent equipment IDEQ-021
EquipmentCombined masthead tricolour/anchor light
Register categoryTopside and navigation lighting
Equipment classEQ
Reported locationMasthead
Inventory stateFitted manufacturer/function owner-confirmed; model suffix and circuit wiring unverified
Manufacturer / modelNASA Marine Combi masthead tricolour/anchor LED; exact manufacturer part number unconfirmed
Serial / part numberNot recorded
Last onboard verificationNot recorded

Original reference and notes: One dual-mode physical lamp in circuit notes, not separate tricolour and anchor devices; switched by polarity.

Electrical installation — as fitted

FieldSurveyed value
Supply voltage / inputNot measured or recorded
Source / distribution busbarNot established
Circuit identifierDC-NAV-01
Primary branch protective deviceCB-001 10 A (owner-confirmed)
Upstream protective deviceNot confirmed
Cable / terminal referencesSW-001 through R3/brown and B4/white in 7 × 1.5 mm² Oceanflex trunk, forecabin junction, then 2 × 1.5 mm² Oceanflex mast cable; exact colour-to-core splice untraced
Cable size, fuse/breaker rating and measured loadCircuit breaker 10 A owner-confirmed; cable size and load current not measured

Important: a device’s manufacturer-rated input, current or recommended fuse is not proof of the actual cable, protection or wiring aboard Ragtime.

Known or reported relationships

  • CB-001 — reported breaker 1,1
  • SW-001 — reported polarity selector
  • TB-002 — R3/brown NASA switched leg; owner-confirmed
  • B4 — B4/white NASA switched leg; owner-confirmed (individual connector group 4 not separately indexed)
  • Historical, superseded: older DPDT notes list B2/blue and Y3/black; these are no longer accepted as the NASA switched pair

The owner confirms one NASA Marine Combi LED, supplied by a separate Oceanflex 2 × 1.5 mm² mast cable with two active polarity-reversible conductors. The two mast cable cores join R3/brown and B4/white of the Oceanflex 7 × 1.5 mm² DC-panel-to-forecabin trunk, and both connect to SW-001 via DC-panel cage clamps. The exact connection of each individual mast cable core to brown versus white at the forecabin junction has not been recorded. The two NASA lamp wires, including its black core, must not be described as a permanent negative-busbar connection, because SW-001 reverses their polarity.

Historical evidence, superseded: The earlier DPDT sketch listed B2/blue and Y3/black as the masthead pair. The photographed handwriting originally marked R3/brown and B4/white as NC in the CB column. The owner has now explicitly corrected the as-fitted masthead pair to R3/B4, superseding both old interpretations without erasing the historical source. The 7-core Y3/black conductor’s possible connection to a common negative busbar remains a separate, unverified assumption. Connector schedule. NASA Marine’s Supernova Combi instructions describe this polarity-switched design; the exact installed model suffix remains unverified. NASA fitting PDF.

Manufacturer reference

NASA Marine combined tricolour/anchor LED confirmed by owner; the specific installed model variant is not yet established. The NASA Supernova Combi product reference and fitting instructions (PDF) document two-wire polarity-mode selection. The fitting instructions call for a 1 A fuse; Ragtime’s reported 10 A panel breaker does not prove presence or absence of smaller downstream protection, or imply cable adequacy.

Information requested from the owner

  1. Confirm the exact NASA Marine Combi LED revision/model, if marked at the masthead or on purchase records.
  2. Verify SW-001 polarity and R3/brown + B4/white trunk → forecabin connector set → 2 × 1.5 mm² NASA mast cable, including which mast-wire insulation joins which trunk conductor; inspect any additional local fuse.
  3. Inspect cable sizes, terminations and antenna/light masthead clearance and note any voltage-drop or functional test measurements.

Record maintenance

  • Evidence basis: existing website inventory, plus explicitly identified manufacturer references where applicable.
  • Verification: pending physical survey; photograph, nameplate data and protective-device references to be recorded.
  • Avoid publishing passwords, SIM identifiers, access tokens or other confidential credentials on this public site.